产品概述： 1、本产品采用高级进口丙烯酸树脂和高级颜料经过细制研磨加工组合而成，适用范围：各种金属、玻璃、陶瓷、石材、电镀(含水电镀)、阳极氧化铝表面、静电喷漆面及烤漆面等制品的丝印及移印，不需加固化剂，不需烘烤，即可获得优异的附着力。 2、产品特性：平光、附着力佳、流平性佳、硬度强、耐酒精、耐冲压、抗刮伤、耐化学品。 3、稀释剂：建议采用本公司配套专用稀释剂开油。 4、固化剂：本产品无需加固化剂，切勿加不配套的固化剂，会影响其效果 5、油墨调配方法：搅拌时先加稀释剂10%左右稀释到印刷适合粘度。 6、干燥时间：表干时间自然挥发5-10分钟，实干时间在24小时以内，48小时后达最佳性能，烤箱80℃烘烤30分钟性能更优。 7、使用期限：半年，过期请弃用，加了其他助剂剩余油墨不可回收。 【油墨使用注意事项】 1、试印确认符合要求后再批量生产。 2、做好被印物的表面清除油脂及杂质工作，以促进附着效果。 3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测，需要完全固化后方可检测。 4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。 5、丝网印刷加适量拉丝膏用本公司特慢干稀释剂更适宜印刷工艺顺畅。 6、注意作业车间的湿度，湿度过大会影响附着力，温度高容易堵网。 【油墨性能检测结果】 1、3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油。 2、纯度99%的酒精500G力在油墨表面来回擦拭100次无脱色。 【油墨使用安全规则】 1、油墨，稀释剂使用及储存时严禁烟火 2、使用时注意施工场所的通风状况良好。 3、尽量避免皮肤直接接触。 4、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。 5、对本品过敏者，使用前应涂覆一层皮肤扶肤膏或戴不渗透手套。 6、注意作业车间的湿度，湿度过大会影响附着力，温度高容易堵网 1, plastic material similar in appearance, but may be of different materials, customers need to try to determine its requirements, and then bulk printing;2, in the printing process, such as drawing or spread out, may be appropriate to add some slow dry plaster;In 3, the ambient temperature is too high, will influence the quality of the original ink;In 4, according to climate change, please stay away from fire, dark environment storage.One, the use of ink technology referencePrinting ink for is to do not have the baking condition without external curing agent and the development of one component high performance ink. The ink has the advantages of convenient use, without curing agent, without baking, can obtain excellent adhesion. Having a flat, adhesive force is good, punching resistance, alcohol resistance characteristics.1 scope of application: iron, aluminum, alloy, glass, ceramic, plating, stone, anodized aluminum surface and baked ( spray paint etc. )2: with the company S-03 diluent diluent3: add TA-9154 curing agent hardening agent 10% increased adhesion, improve the ink film hardness.The 4 squeegee hardness: 70-80 degrees appropriate, the other point of view in the 60-70 degrees is the best.5: suitable for 100-420 screen printing mesh6: amount with 300 mesh screen every kilograms about Printing 30 square meters.The 7 drying methods: TA series belongs to natural volatile drying inks, ink layer surface dry time drying time: 5-10 minutes in 24 hours.After 48 hours to achieve the best performance of 1 or add TA-9154 hardening agent 10% can increase the adhesion, improve the ink film hardness. 2 90℃oven and bake for 20 minutes and ***o, test method for ( completely dry )1, row grid with 3M after tape stripping at least 3 times above, no drop ink phenomenon.In 2, impregnated with a purity of 99% alcohol tampon, 500G force on the surface of the printing ink rub 200 times without decolorization.Three, the use of ink.1 print test confirmation after the mass production.2 be printed material surface to remove grease and impurity, to promote the attachment effect.3 need to register, should be in the first color table stem or stem and then register work.The 4 adhesion, hardness, acid resistance, oil resistance, resistance to stains oily, scratch resistance, abrasion resistance and other performance test, need ink layer is completely cured before detection.5 without permission, may not use the series of ink and other types of ink mixing and matching.6 adding curing agent after the use of time: the curing agent is added after the ink using time for 4~6 hours, the higher ambient temperature using the shorter the time, the remaining ink unrecyclable.
手机版丝印网
手机版APP（安卓）
显示原图
免责声明：以上信息由会员自行提供，内容的真实性、准确性和合法性由发布会员负责。丝印特印网对此不承担任何责任。
印铁油墨